Download a printable version of the below tutorial here. This information is taken from a demonstration delivered by Dr. Willis Pumphrey, DDS in 2010. It is intended to serve as a general guide and is in no way a comprehensive instruction manual for performing IPR. As always, doctors must rely on their own best judgement.

When performing IPR its recommended in the following increments:

• 0.1mm on an anterior tooth
• 0.2mm on an anterior tooth
• 0.2mm on a posterior tooth
• 0.3mm on a posterior tooth

---

0.1mm on an anterior tooth

To perform 0.1mm on an anterior tooth, perform the following steps:
NOTE: You will need the following parts: 

• Medium diamond strip (view item)
• IPR gauges

1.Cut diamond strip in half. You will only need one half of the strip per procedure.



2.Gently move the strip backwards and forwards between the teeth along the contact area in a sawing motion. It takes roughly 8-12 motions, but ultimately depends on the patient.



3.Flip the strip over, and perform this action again, about 8-12 times. Rinse the area.



4. Take the 0.1mm gauge and place in between the two teeth to verify the correct amount of space.

NOTE: If the gauge does not fit in between those teeth, continue to file between the tooth surfaces until the desired result is reached.

---

0.2mm on an anterior tooth

To perform 0.2mm on an anterior tooth, perform the following steps:
NOTE: You will need the following parts: 

• Upper or lower-coated diamond disc (view item)
• IPR gauges
• Optional: Fine or extra-fine diamond strip (view item)

The single-sided diamond disc that you will utilize to perform this procedure depends on the tooth that you wish to reduce and the direction of movement. You can determine this by checking the tooth charts on your treatment plan.

1. Line up the disc parallel to the contact area.



2. Turn the drill on and move the disc along the contact area. Stop at the height of the interdental papilla, or when you feel the contact break.



3. If needed, use floss to ensure that the contact has broken. You may also use a diamond strip to file down any sharp corners or rough surfaces left from the disc.



4. You may use a diamond strip to file down any sharp corners or rough surfaces left from the disc.



5. Rinse the area, then take the 0.2mm gauge and place in between the two teeth to verify the correct amount of space.

---

0.2mm on a posterior tooth

To perform 0.2mm on an posterior tooth, perform the following steps:
NOTE: You will need the following parts: 

• Upper or lower-coated diamond disc (view item)
• IPR gauges
• Optional: fine or extra-fine diamond strip (view item)

The single-sided diamond disc that you will utilize to perform this procedure depends on the tooth that you wish to reduce and the direction of movement. You can determine this by checking the tooth charts on your treatment plan.

1. Have a dental assistant hold back the patient's lips and cheeks, to prevent them from getting cut. Have the assistant hold the tongue down with a mirror or retractor. If needed, extend the neck of the drill so that the disc does not interfere with the anterior teeth during the procedure.



2. Line up the disc parallel to the contact area. Turn the drill on and move the disc along the contact area, from facial to lingual. Stop at the height of the interdental papilla, or when you feel the contact break.



3. If needed, use floss to ensure that the contact has broken. You may also use a diamond strip to file down any sharp corners or rough surfaces left from the disc.



4. Take the 0.2mm gauge and place in between the two teeth to verify the correct amount of space.

---

0.3mm on a posterior tooth

To perform 0.3mm on an posterior tooth, perform the following steps:
NOTE: You will need the following parts: 

• Double-sided diamond disc (view item)
• IPR gauges

1. Have a dental assistant hold back the patient's lips and cheeks, to prevent them from getting cut. Have the assistant hold the tongue down with a mirror or retractor. If needed, extend the neck of the drill so that the disc does not interfere with the anterior teeth during the procedure.



2. Line up the disc parallel to the contact area. Turn the drill on and move the disc along the contact area, from facial to lingual. Stop at the height of the interdental papilla, or when you feel the contact break.



3. Rinse, then use the 0.3mm gauge to verify the correct amount of space.